The procedure for converting RVK3B 4 / 0-2 / 2 single-sided four-color printing to bottom two-color printing is as follows: 1. Open the cover on the side of the engine, and then press the front brake until the pointer (1) is aligned with the zero position (the minute adjustment is turned by hand). RVK3B 2/2 chinging shat Aige bottom two-color printing conversion paper procedures are as follows: 1. Turn the selection switch (b) to the right, "the bottom printing and the engine switch (c) to the right. The procedure of RVK3B 2 / 2-4 / 0 bottom two-color printing to single-side four-color printing is as follows: 1. Open the hood next to the engine, and then press the front button until the pointer (8) comes out.
A beautiful Flower Pot will bright up your Home Decoration and provide suitable habitat for your lovely plants. You can do some gardening during your spare time to ease your tiredness and pressure. Planting adorable greenery, flowers, succulents, or ferns, you can experience wonderful rurality in your home.
Ceramic is a nice material that has been fired in the heating kiln to come into being the final form of a beautiful container. Our Flower Pot is elaborately handcrafted so it's rather durable and sturdy that could serve for years whether indoors or outdoors.
Unique design with exquisite embossment pattern, versatile style and light luxury texture, bring a touch of nobility to your bedroom, living room, dining room, office, shopping mall, hotel, Garden, etc. Not only a plant pot but also a piece of art.
Garden decoration, Garden gifts, Ceramic Pots for Plants, Pots and Planters, etc HISMOK(SHENZHEN)TECHNOLOGY CO.,LTD , https://www.fzwilltrade.com
2. Turn the swing button (b) to the right of the "bottom printing machine" and the engine button (c) to the right.
3. Press the steering lever (2).
4. Pull out the pin clamp (3) in the feed cylinder, then pull out the latch (4) and loosen the clamping screw (5).
5. Place the carousel roller on the pulley to adjust the paper size on the scale (6).
6. Tighten the clamping screw (5).
7. Slightly shake the front and back of the pulley until there is slight resistance, then turn the car roll to the position between them and take out the car roll.
8. Pull back the pin clamp (3) in the feed cylinder.
9. Close the cover and-twist the selection switch (b) to the middle position to "continue printing". -Turn the engine switch (c) to the left. -Turn "Bottom printing air pump stop" (a) to the right.
10. Turn the bracelet (7) to "print the mark on the bottom" to adjust the opening and closing time of the middle paper conveyor.
11. Ready to boot.
2. Open the cover on the side of the engine, then remove the pin clamp (3) and loosen the screw (5) in the feed cylinder.
3. Put the turning roller into the belt pulley and rotate to the required paper size on the scale.
4. Tighten the clamping screw (5).
5. Use the turning roller to turn the pulley back and forth until there is a slight resistance. Then turn the car roll between the two and remove the car roll.
6. Pull the pin clamp (3) on the feed cylinder back to its original position.
7. Close the cover and-open the "bottom printing air pump switch" (a) to the right.
-Twist the switch (b) to go to the middle and "continue printing".
-Turn the engine toggle (c) to the left.
8. If necessary, turn the bracelet (7) to adjust the opening and closing time of the intermediate paper conveyor.
9. Ready to boot.
2. Turn off the "Bottom Printing Air Pump Switch" (a) (middle position), twist the single-sided printing switch (b) to the left, and twist the engine switch (c) to the right.
3. Remove and loosen the clamping screw (5) from the pin clamp (3) of the feed cylinder.
4. Put the turning roller into the pulley until the pointer (8) is aligned with the printed mark on one side.
5. Replace the latch (4) and tighten the clamping screw (5).
6. Turn the pulley back and forth until there is a slight resistance, and then move the turning roller between the two and take out the turning roller.
7. Pull the pin clamp (3) in the feed cylinder back to its original position.
8. Turn the pulley until the pointer (1) is aligned with the zero position, and then close the cover.
9. Pull the steering rod (a).
10. Turn the selector switch (b) to the middle position and turn the engine switch (c) to the left.
11. Turn the bracelet (7) to print the mark on one side.
12. Ready to boot.
Planting brings a lot of fun