The printing press is the central equipment of the printing plant, and also one of the equipments with the highest utilization rate among all the equipment of the printing plant. In order to ensure the normal operation of the printing press, daily maintenance and maintenance are essential and very necessary. The daily maintenance and maintenance of the printing press is an important task in the management of printing equipment. The following is a brief talk about the daily maintenance and maintenance of the machine from the following aspects. 1. Static maintenance of printing machine The static maintenance of the printing machine refers to the maintenance of the machine in the static state. 1. Establish rules and regulations for machine maintenance. The maintenance of the offset press should be based on the instruction manual of the machine. Such as regular oil changes, filter cleaning, and regular inspection of machine accuracy. 2. Strengthen the maintenance of important parts. Gears, cams, sprockets, rollers and bearings are the most important parts on the printing press, and their maintenance is different from other parts, because changes in their accuracy will affect the final printing quality. The spring is the most used part of the machine for the force balance mechanism. The quality of their work directly determines the accuracy of the coordination of the moving parts. The spring must have sensitive elasticity. Extremely unfavorable. If the above problem is found, the spring needs to be replaced immediately. 3. Carry out technical reforms and strengthen machine maintenance. Machine maintenance requires that the machine be designed with the convenience of machine maintenance in mind. However, due to the complexity of the printing press, it is obviously impossible to consider each factor, and the content of machine maintenance will also change due to environmental changes. Therefore, it is necessary to improve the structure that is not conducive to machine maintenance without affecting the normal work. Second, the dynamic maintenance of the printing press The dynamic maintenance of the printing machine refers to the maintenance of the machine under the dynamic state of the printing machine. The static maintenance of the machine is the premise of the dynamic maintenance of the machine. At the same time, the dynamic operation of the machine can in turn detect the level of static maintenance of the machine. The dynamic maintenance of the machine is very important. The main contents that should be maintained under the dynamic state of the machine are analyzed from the following aspects. 1. Machine preparation status detection. The ready state of the machine can be checked by jogging or turning. Other tools such as tools are stuck in the machine; whether the installation position of the printing plate is suitable, if it is not suitable, it may damage the printing plate or cause great difficulty in finding rules; if the installation of the blanket is suitable, if it is not suitable, it may be It may cause printing failure. In severe cases, the blanket or machine may be damaged. 2. The lubrication state of the machine. First of all, you can observe whether the oil path of the machine is unobstructed through the oil mark. If there is no oil in the oil mark or the observation is not clear at the oil mark, you should stop the engine and check the oil path carefully for oil leakage. Although the leakage of the machine is easy to observe, it is difficult to find the cause. For machines such as sliding bearings, low speed is not conducive to lubrication, especially jog or low-speed operation has a greater impact on its lubrication. Therefore, before carrying out such operations, it is best to lubricate the idling machine first, which is also a primary task that should be done before going to work every day. The oil pump of some machines is driven by the host, so when the point is reversed, not only can the oil circuit not be refueled, but the oil in the oil circuit will be sucked back to the tank. This is very dangerous, so the reverse point should be avoided. The lubrication of some more important parts can also be detected by the temperature of the metal near it. If the temperature is too high, it indicates that there is a problem with the lubrication. 3. Impact during the operation of the machine. The smaller the impact during the operation of the machine, the more beneficial it is to printing, and at the same time it can extend the service life of the machine. Reducing the printing pressure (pressure in a broad sense) is an important condition to ensure the smooth operation of the machine. Under the premise of ensuring the quality of the printing, the smaller the printing pressure, the better. Reducing the speed of the machine is another important condition for reducing the rotational inertia of the machine. The lower the speed of the machine, the smaller the inertia of the machine. Therefore, the machine should not be kept at high speed all the time. The above aspects are only part of the daily maintenance and maintenance of the printing press. The quality of the daily maintenance and maintenance of the printing press directly affects the service life and product quality of the printing press, so it cannot be taken lightly.
Watch box insert a pillow or a foam with velvet in the box in order to protect the watch,like the below pictures.
Also box size is almost detain as 10X10X10CM or 9X9X9CM.
Box style keep as below and did not change much.
The logo will be put on the top of box or inside of top of box, normally use hot stamp.
size and color could be customized according to your requires.
Wooden Watch Box,Watch Packing Tin Box ,Pu Leather Watch Box,Plastic Watch Box Shenzhen Haotuanyuan International Trading Co.,Ltd , https://www.luxurypaperbox.com
