Knowing the structure and performance of the testing instrument for carton production, correctly mastering the use method and brief maintenance and repair skills of the instrument used, can prolong the service life of the testing instrument, improve the detection accuracy, and also facilitate the quality inspection personnel to carry out quality monitoring work. And can greatly improve the inspection work efficiency and the monitoring quality of raw materials and carton products. In the following, we will communicate with our peers about the simple maintenance and precautions concerning the testing equipment for carton production. Brief maintenance and repair skills It is necessary to grasp the operating procedures, detection ranges of food use methods, so as not to affect the measurement. The moisture-proof, rust-proof, dust-proof, shock-proof and calibration levels of the mechanical parts of the instrument should be well done, and the specified type of lubricating grease should be injected. The original components, power supplies, sensors, converters, and displays of the electrical parts should be insulated, rodent-proof, and temperature-controlled to reduce damage to the electrical parts due to oxidation, aging, leakage, short circuit, and open circuit. All kinds of glassware and optical instruments should be handled lightly and placed gently to prevent sudden cooling, sudden heat, impact, collision, dust and mildew. Especially the mirror surface and polished surface of the optical parts can not be taken directly by hand. They should be worn with soft gauze gloves or pads. When wiping, they can only be wiped with a fine silk cloth. Knife edges, scales, and indicators on various measuring instruments should be protected from damage, kept clean, and regularly calibrated by the measuring department. For the mechanical system due to wear, rust, dust, oil stains, breakage, damage, falling into foreign objects, loose or improper operation, the relevant moving parts appear "dead", slip, vibration, asynchronous operation, screw screw can not be adjusted, sound temperature Abnormalities can be checked by watching, listening, measuring and touching. It does not move when an electrical fault occurs, the indicator light is off, the display does not display or the data display is abnormal, you can check the switch, fuse, filament, electrical device for leakage, or poor contact, and can measure the resistance, voltage, current, and inject the corresponding Signal, replace the original device in question to check. The deformation of the pointer, the wear of the scale, the peeling of the paint, the blurring, the interruption of the electrical signal of the display, or the abnormal electrical parameters that affect the normal display and accurate readings should be replaced. Instrument disassembly Judging the condition of the instrument through analysis, if there is indeed a fault, it can be disassembled, and carefully observe the mutual assembly relationship of various parts before starting. Assembly accuracy and disassembly procedures are best recorded for disassembly of complex parts to prevent errors during recovery. Do not forcibly disassemble parts that are not easy to disassemble. Instead, select rubber, plastic, or wooden hammers, and gently tap to loosen them slightly before disassembling. Parts of different materials such as metal, rubber, glass, magnetic body, etc., should be stored separately, at the same time to prevent loss, especially after being magnetized, it will affect the use. For parts that do not have to be disassembled, never disassemble easily. It is best to ask professional machinery to repair the faults that you are not sure to solve. Assembly after overhaul After the replacement and repair of the damaged, defective, deformed, deteriorated, corroded, worn, broken, loose, leaked and other defective parts, the assembly should be restored according to the original procedure. The accuracy must be within the tolerance range. The requirements in the horizontal state (zero position) can not be omitted. If you use lubricating oil, please pay attention to the type of lubricating oil used and the order of oil injection. After the repair and installation of the instrument is completed, it must be tested with no-load and real-load. If it directly affects the measurement reading, it should also be marked: Verification by the measurement department to ensure that the data detected by the instrument and the performance parameters of the instrument are in compliance. It is required that the use of the operation should be identified and the records should be archived. A cast iron pot / casserole is a large, deep dish used both in the oven and as a serving vessel. The word is also used for the food cooked and served in such a vessel, with the cookware itself called a casserole dish or casserole pan. Cast Iron Pots,Oval Cast Iron Pots,Wood Handle Cast Iron Pots Shijiazhuang Ever Fresh Trading Co., Ltd. , https://www.efhomedeco.com
Casserole cooking is generally done in an oven to bake where heat circulates all around the cooking vessel. Casseroles may be cooked covered or uncovered, while braises are typically covered to prevent evaporation.
EF Homedeco can supply difference sizes casserole to meet customer`s request, from round to square, from seasoned finish to enameling, customer designs can be available.